一本色道久久综合精品竹菊_日韩欧美亚洲综合_日韩中文字幕一区二区_精品入口麻豆88视频

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

swager cylinder Sold to Nigeria

Release time:2023-12-11 09:05:14 Hits: Current position: Home > News

This article mainly introduces:

Nigeria hydraulic cylinder,swager cylinder manufacturer,swager cylinder

Nigeria swager cylinder

(Nigeria swager cylinder,produced by Hengyu Hydraulic Cylinder Factory)

swager cylinder are widely used in Nigeria,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed swager cylinder for customers from Nigeria.

Introduction to swager cylinder:

1, the hydraulic machinery should be kept clean, in order to prevent dust and debris from falling into the oil, the tank should be sealed. 2, the oil in the tank should be replaced regularly according to the working condition. When changing the oil, the dirt and impurities accumulated at the bottom of the tank should be removed and the tank should be cleaned. 3, hydraulic oil, oil drums should be set in a clean and safe place to strengthen management. The oil drum, oil filter, oil funnel, oil pipe, etc. used should be kept clean. The oil drums for loading hydraulic oil must be cleaned in advance, and the oil drums should be dedicated and not mixed with other oil drums.

The material, shape and compression of the swager cylinder seal have a great impact on the service life and work efficiency of the swager cylinder. In addition to requiring a reliable seal, it should also have a long service life and less friction loss. At present, there are many seal manufacturers in the country, and it is also crucial to choose high-quality seals with reliable and stable quality.

When the swager cylinder is installed on the main engine, the oil port piping part and the guide sleeve should be checked for oil leakage in the running test, and the earring and the middle hinge shaft bearing should be refueled.

Before the swager cylinder is removed, the system should be unloaded, the loop pressure is zero, the oil source should be cut off, and the oil port should be blocked after the oil port distribution pipe is loosened.

Answers to some questions about swager cylinder:

100 tons press, the cylinder diameter is 250, how much pressure?
100 tons hydraulic press, if it is a single acting hydraulic cylinder, the required oil pressure is the nominal force divided by the cross-sectional area of the cylinder piston. One hundred tons of its pressure is 1000 kN (1000000N), the diameter of the cylinder is 250 mm, its area is the circular rate multiplied by the square of the radius, is 49062.5 square mm, and then the pressure divided by the area of the oil pressure is 20.38MPa. Therefore, a hydraulic pressure of 20.38 mpa is required for a 250 diameter cylinder to obtain 100 tons of pressure.

What brand of hydraulic cylinder seal ring is best?
Depending on the specific product, the world famous seal brands are NOK, CFW, PARKER, TSS, WKF, DINGZING DZ, ASTON, HALLITE, TECNOLAN and so on.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
主站蜘蛛池模板: 澳门| 昌平区| 桂阳县| 九寨沟县| 桐乡市| 江西省| 达州市| 荥经县| 体育| 丁青县| 安仁县| 梨树县| 贡嘎县| 广河县| 宣城市| 嵩明县| 双城市| 宜章县| 应城市| 长子县| 二连浩特市| 常山县| 蕉岭县| 临邑县| 清远市| 江门市| 封开县| 通化市| 大方县| 甘谷县| 开远市| 田东县| 长岛县| 抚顺县| 大方县| 高雄市| 武宣县| 离岛区| 永胜县| 昌吉市| 高唐县|