一本色道久久综合精品竹菊_日韩欧美亚洲综合_日韩中文字幕一区二区_精品入口麻豆88视频

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

pusher hydraulic cylinder Sold to Turkey

Release time:2023-12-02 14:47:40 Hits: Current position: Home > News

This article mainly introduces:

Turkey hydraulic cylinder,pusher hydraulic cylinder manufacturer,pusher hydraulic cylinder

Turkey pusher hydraulic cylinder

(Turkey pusher hydraulic cylinder,produced by Hengyu Group)

pusher hydraulic cylinder are widely used in Turkey,because of simple structure and reliable operation,excellent temperature resistance,no transmission clearance.So our company has designed pusher hydraulic cylinder for customers from Turkey.

Introduction to pusher hydraulic cylinder:

The pressure of the sliding surface of the pusher hydraulic cylinder piston is too large, resulting in sintering. The piston tilts due to the weight of the piston rod, resulting in the phenomenon of non-stiffness, or the pressure of the sliding surface of the piston rises due to the action of the transverse load, which will cause sintering. In the design of the pusher hydraulic cylinder must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.

Disassembly pusher hydraulic cylinder: When disassembly pusher hydraulic cylinder, strictly prevent damage to the screw thread at the top of the piston rod, the screw thread of the pusher hydraulic cylinder head and the surface of the piston rod. It should also be noted that the piston cannot be played out from the pusher hydraulic cylinder.

In use, the pusher hydraulic cylinder should try to avoid the friction iron powder or iron filings formed by buffering the plunger. When the matching gap of the buffer device is small and the transverse load on the piston rod is large, the sintering phenomenon may be caused. These friction iron powder or the metal fragments that have fallen off as a result of sintering will remain in the pusher hydraulic cylinder.

When the pusher hydraulic cylinder is in use, once the seal and guide support ring are found to be defective, the seal with the same structural form and appropriate material should be replaced according to the structural form of the pusher hydraulic cylinder seal to be repaired, so as to minimize the thickness of the oil film between the seal and the sealing surface and reduce the leakage of the seal.

Answers to some questions about pusher hydraulic cylinder:

Hydraulic system schematic diagram, pipeline identification S and L, respectively corresponding nominal diameters? 16S is equivalent to DN12 high-pressure cylinder, and 15L means what?
16S refers to the high pressure series, outer diameter 16x2 steel pipe, the corresponding sleeve nut is M24X1.515L is the low pressure series, the outer diameter of 15x1.5 steel pipe, the corresponding sleeve nut is M22X1.5.

Why the lifting cylinder falling by itself?
May be there is a pressure relief point. Check and repair the following parts: whether there is oil leakage in the transparent pipe at the top of the cylinder: the cylinder oil seal is broken, and the cylinder and oil seal need to be replaced; No: The multiway valve has pressure relief and needs to be repaired. Maintenance in accordance with routine maintenance items can reduce mechanical failures: 1. Check whether the thermostat works normally. 2, check the transmission shift work is normal. 3. Check the tightness of the fan belt. 4, check whether the diesel tank oil inlet filter is blocked or damaged, and clean or replace the filter. 5. Check and adjust the valve clearance.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
主站蜘蛛池模板: 乌什县| 宜川县| 涿州市| 如东县| 大厂| 云梦县| 庆云县| 江都市| 城步| 盐津县| 黎川县| 晋中市| 黑水县| 柳河县| 建始县| 琼中| 丹阳市| 祁连县| 大埔区| 鹤山市| 察隅县| 高唐县| 巢湖市| 海门市| 云梦县| 会宁县| 墨竹工卡县| 铜川市| 银川市| 武功县| 镇安县| 河津市| 榆社县| 兴和县| 宁陵县| 马边| 洛宁县| 龙井市| 杭锦后旗| 普宁市| 天镇县|