一本色道久久综合精品竹菊_日韩欧美亚洲综合_日韩中文字幕一区二区_精品入口麻豆88视频

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

hydraulic jig cylinder Sold to Norway

Release time:2023-11-08 10:36:32 Hits: Current position: Home > News

This article mainly introduces:

Norway hydraulic cylinder,hydraulic jig cylinder manufacturer,hydraulic jig cylinder

Norway hydraulic jig cylinder

(Norway hydraulic jig cylinder,produced by Hengyu Group)

hydraulic jig cylinder are widely used in Norway,because of powerful torque,clever hydraulic energy conversion,simple structure and reliable operation.So our company has designed hydraulic jig cylinder for customers from Norway.

Introduction to hydraulic jig cylinder:

If air enters the hydraulic system, the hydraulic jig cylinder will not operate normally, mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced.

The pressure of the sliding surface of the hydraulic jig cylinder piston is too large, resulting in sintering. The piston tilts due to the weight of the piston rod, resulting in the phenomenon of non-stiffness, or the pressure of the sliding surface of the piston rises due to the action of the transverse load, which will cause sintering. In the design of the hydraulic jig cylinder must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.

When the hydraulic jig cylinder is in use, ensure that the hydraulic jig cylinder and the surrounding environment should be clean. The tank should be sealed to prevent contamination. Pipelines and fuel tanks should be cleaned to prevent falling off the oxide sheet and other debris. Clean with lint-free cloth or special paper. Twine and binder should not be used as sealing materials. Hydraulic oil according to the design requirements, pay attention to the change of oil temperature and oil pressure. When there is no load, unscrew the exhaust bolt for exhaust.

How the cavitation of the hydraulic jig cylinder is formed: With the gradual rise of pressure, the gas in the oil will become bubbles, when the pressure rises to a certain limit value, these bubbles will break under the action of high pressure, so that the high temperature and high pressure gas will quickly act on the surface of the parts, resulting in cavitation of the hydraulic jig cylinder, resulting in corrosive damage to the parts.

Answers to some questions about hydraulic jig cylinder:

Why is there noise in the hydraulic cylinder of the excavator lift arm?
There is no noise of a normal cylinder, check whether the throttle is ringing, or the mechanical part connected with it is ringing, and the mechanical part can be greased. If it can't be ruled out, disconnect the cylinder from the mechanical part and act alone to see what the situation is.

What is the cause of sound and vibration when the hydraulic cylinder is under load?
The main reason 1) may be that the load machinery has stuck phenomenon, and the resistance is large. 2) The hydraulic oil is not enough, or the filter is blocked by dirty things, and the oil is flooded. 3) There is a problem with the pump.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
主站蜘蛛池模板: 京山县| 龙井市| 临潭县| 阿克陶县| 天等县| 元朗区| 泽普县| 唐海县| 兴安县| 陆丰市| 宣化县| 芦山县| 台安县| 民丰县| 罗源县| 泽库县| 蛟河市| 余干县| 夹江县| 沙湾县| 翼城县| 武陟县| 湘潭县| 马关县| 大姚县| 湛江市| 洛阳市| 永州市| 黎川县| 西丰县| 金秀| 义马市| 华阴市| 平乐县| 南宫市| 来凤县| 麦盖提县| 凉城县| 宁海县| 兴业县| 张北县|