一本色道久久综合精品竹菊_日韩欧美亚洲综合_日韩中文字幕一区二区_精品入口麻豆88视频

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

booster cylinder Sold to Canada

Release time:2023-11-12 15:33:01 Hits: Current position: Home > News

This article mainly introduces:

Canada hydraulic cylinder,booster cylinder manufacturer,booster cylinder

Canada booster cylinder

(Canada booster cylinder,produced by Hengyu Group)

booster cylinder are widely used in Canada,because of powerful torque,clever hydraulic energy conversion,simple structure and reliable operation.So our company has designed booster cylinder for customers from Canada.

Introduction to booster cylinder:

The booster cylinder should not be mixed with foreign objects during assembly, which will cause scars. Before the total assembly of the booster cylinder, all parts must be fully removed and cleaned. When the parts are installed with burrs or dirt, foreign objects are easily embedded into the surface of the booster cylinder wall due to the stiffness and the weight of the parts, causing scars.

When the initial action of the booster cylinder is slow, please check the temperature of the hydraulic system, because in the case of low temperature, the viscosity of the hydraulic oil is large and the fluidity is poor, resulting in slow action of the booster cylinder. The improvement method is to replace the hydraulic oil with good viscosity temperature performance, and the oil temperature at low temperature can be increased by heater or heating by the machine itself, and the normal working oil temperature of the system should be maintained at about 40 ° C.

booster cylinder can not drive the load troubleshooting: oil pressure is too low. booster cylinder selection specifications are too small. Leakage in booster cylinder or associated hydraulic system element.

In the process of using the booster cylinder, sometimes such a problem will occur, the booster cylinder can not act immediately after the instruction of the booster cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil booster cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

Answers to some questions about booster cylinder:

How big is the pump and motor for 20 tons of hydraulic cylinder?
According to the working pressure of 25 mpa estimate, the cylinder should use 100mm bore, 63mm piston rod, stroke 40mm. According to 30 reciprocating calculation, the flow rate is about 25 liters/minute. The motor power is 11 kW, want to be cheap, use 25SCY14-1B oil pump can be.

How to change the seal ring of lift oil cylinder of forklift truck?
Remove the cylinder, put it on the vise, first screw off the big nut plug on the head, and then pull out the guide sleeve, you can directly pull out the core of the cylinder, if it is to change the seal of the cylinder head, the core does not need to be pulled out, if it is to change the seal inside, pull it out and see the oil seal, remove it and replace it, there are three seals of the cylinder head, the inner seal, The outer seal, dustproof, it is best to replace them all together, and be sure to keep them clean when changing, and you can lubricate them with clean hydraulic oil.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
主站蜘蛛池模板: 河津市| 成武县| 新巴尔虎左旗| 屏山县| 济南市| 绥阳县| 浦县| 乐至县| 芜湖市| 特克斯县| 神农架林区| 南丰县| 高清| 京山县| 手机| 新野县| 甘谷县| 响水县| 兴山县| 新乡市| 镇沅| 台中市| 衢州市| 德安县| 都匀市| 本溪| 大厂| 孟连| 汉寿县| 信宜市| 长汀县| 通州区| 东源县| 淮滨县| 新沂市| 隆昌县| 芮城县| 延安市| 穆棱市| 屏山县| 白河县|